1-800-627-3010

SCIGRIP IPS Weld-On #1910 - Slow-Curing High-Strength Flexible Vinyl Cement

This product must be shipped via a ground service

  • Sale
  • Regular price $0.00


Description

General Description

Weld-On 1910 is a clear, medium bodied, high strength solvent cement. It cures rapidly with the dissipation of the solvent at room temperature resulting in a very strong, flexible, water resistant bond. Indications are that service life for a number of years may be expected under normal use, but some yellowing may be expected.

Substrate Recommendations

Flexible or rigid vinyl to itself or a variety of other plastics and non-plastics.

Bonding Recommendations

Weld-On 1910 is high strength cement that is being used by a number of companies for bonding flexible vinyl to itself, flexible to rigid vinyl, ABS, acrylic, canvas and other porous materials. It is also being used to repair vinyl seats in buses, patch vinyl waterbeds, etc.

Additional Information

This product must be shipped via a ground service.

Technical

Technical Data Sheet (TDS)

Typical Bond Strength†

Substrate Material Aged Bond Strength, lbs/in(kg/cm2)
2 Hours 24 Hours 1 Week
PVC 250 650 1,000
ABS 150 500 1,000

† Substrate thickness: 0.25 inch (0.64 cm). Bond area: 1.0 in² (6.45 cm²). Ultimate Bond Strength is defined as strength achieved after 24-hour room temperature cure.

Adhesive Properties and Characteristics @ 73°F (23°C)

Color Clear

Viscosity

2100 ± 100 cps

Working Time

15 Minutes

Fixture Time (Time to reach 80% of ultimate strength)

20-25 Minutes

Time to reach Ultimate Bond Strength

72 Hours

Specific Gravity (g/cc)

0.924 ± 0.01
Coverage

10 mil: 32 sq ft/pint 280 sq ft/gallon

20 mil: 16 sq ft/pint 130 sq ft/gallon

Directions

Directions for Use

Clean surfaces to be joined.

Coat each mating surface. Weld-On 1910 may be applied with brush, syringe, gun, etc. Press parts together immediately and hold a few seconds until “grab” begins – or for quicker initial set: coat each surface and wait 10 to 20 seconds, then press firmly together.

If not possible to coat both surfaces, give generous coat to one and press gently to other to wet it. Then apply nominal pressure.

Good strength will develop in a few minutes with some materials. Bond strength will be considerable in a few hours and will reach high strength in 24 to 48 hours. Thereafter, strength will continue to increase gradually for some weeks.

Shelf Life

Three years expectancy in tightly sealed containers. Stability of the product is limited by the permanence of the container and the evaporation of the solvent when container is open. Evaporation of solvent will cause the cement to thicken and reduce the effectiveness of the cement.

Safety

Safety Data Sheet (SDS)

Safety and Environmental Precautions

This product is a flammable, fast evaporating, solvent. It is considered a hazardous material. In conformance with the Federal Hazardous Substances Labeling Act, the following hazards and precautions are given. Purchasers who may repackage this product must also conform to all local, state and federal labeling, safety and other regulations.

DANGER: EXTREMELY FLAMMABLE. VAPOR HARMFUL. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE SKIN OR EYES.

Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store away from direct sunlight between 40º F – 110ºF (5º C – 43ºC). Use only with adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values contained in Section II and VIII of the Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency and other conditions where short-term exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, safety goggles and impervious apron should be used. Carefully read Material Safety Data Sheet and follow all precautions.

Contains Tetrahydrofuran (109-99-9), Methyl Ethyl Ketone (78-93-3) and Cyclohexanone (108-94-1). Do not use this product for other than intended use.

“Title III Section 313 Supplier Notification”: This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all Material Safety Data Sheets that are copied and distributed for this material.

First Aid

Inhalation: If overcome with vapors, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.

Eye Contact: Flush with plenty of water for 15 minutes and call a physician.

Skin Contact: Wash skin with plenty of soap and water for at least 15 minutes. If irritation develops, get medical attention.

Ingestion: If swallowed, give 1 or 2 glasses of water or milk. Do not induce vomiting. Contact physician or poison control center immediately.