Weld-On 45 is a fast curing, two-component, low VOC, reactive adhesive. When mixed and applied, it polymerizes at room temperature to form high strength bonds within an hour. The adhesive has excellent corrosion resistance, good gap-filling capabilities, weatherability and outstanding impact strength at low and high temperatures. Once cured, the adhesive will withstand a temperature range of -20° F (-29° C) to 200° F (93° C). The elongation will remain the same even at high temperatures up to 200° F (93° C). UL 746C (aluminum, fiberglass).
Weld-On 45 is formulated for bonding a wide variety of metals, plastics and many other substrates.
Weld-On 45 is recommended for a variety of applications and industries including sign assembly and other fabrication and manufacturing uses where high bond strength and environmental resistance is required. This adhesive is especially suitable for bonding aluminum, CRS, brass, copper, galvanized steel and other metals. Excellent adhesion is also obtained on plastics such as PVC, polycarbonate, ABS, acrylic and PETG.
This product must be shipped via a ground service.
Technical Data Sheet (TDS)
Typical Bond Strength†
† Substrate thickness: 0.25 inch (0.64 cm). Bond area: 1.0 in² (6.45 cm²). Bond strength data was obtained using the compressive shear strength method (ASTM D-2564). Ultimate Bond Strength is defined as strength achieved after 24-hour room temperature cure.
Adhesive Properties and Characteristics @ 73°F (23°C)
Directions for Use
Weld-On 45 is packaged in a twin-syringe cartridge that dispenses product in a 4:1 mix ratio. The cartridge must be inserted in the dispensing gun and the mixing tip attached prior to dispensing.
One year in unopened cartridge. The date code of manufacture is stamped on the bottom of the cartridge. Shelf life is reduced at higher temperatures and enhanced at lower temperatures. To optimize shelf life, refrigerator storage is recommended and/or store away from direct sunlight between 50° F – 80° F (10° C – 27° C). Keep away from sources of heat, open flame, sparks, sunlight and moisture.
Safety Data Sheet (SDS)
Safety and Environmental Precautions
This product is a flammable, reactive adhesive. It is considered a hazardous material. In conformance with the Federal Hazardous Substance Labeling Act, the following hazards and precautions are given. Purchasers who may re-package this product must also conform to all local, state, and federal labeling, safety and other regulations. VOC emissions do not exceed 250 grams per liter.
DANGER! FLAMMABLE. VAPOR HARMFUL. MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE SKIN OR EYES.
Keep out of reach of children. Do not take internally. Keep away from heat, spark, open flame and other sources of ignition. Keep container closed when not in use. Store away from direct sunlight between 50° F – 80° F (10° C – 27° C). Use only in adequate ventilation. Avoid breathing of vapors. Atmospheric levels should be maintained below established exposure limit values. See Section II of Material Safety Data Sheet. If airborne concentrations exceed those limits, use of a NIOSH-approved organic vapor cartridge respirator with full face-piece is recommended. The effectiveness of an air-purifying respirator is limited. Use it only for a single short-term exposure. For emergency and other conditions where short-term exposure guidelines may be exceeded, use an approved positive pressure self-contained breathing apparatus. Do not smoke, eat or drink while working with this product. Avoid contact with skin, eyes and clothing. May cause eye injury. Protective equipment such as gloves, goggles and impervious apron should be used. Carefully read Material Safety Data Sheet and follow all precautions.
Component A contains Methyl Methacrylate Monomer (80-62-6). Component B contains Catalyst-Initiator and Benzoyl Peroxide (94-36-0). Do not use this product for other than intended uses.
“Title III Section 313 Supplier Notification:” This product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40CFR372. This information must be included in all Material Safety Data Sheets that are copied and distributed for this material.
Inhalation: If overcome with vapors, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Call physician.
Eye Contact: Flush with plenty of water for 15 minutes and call a physician.
Skin Contact: Wash skin with plenty of soap and water for at least 15 minutes. If irritation develops, get medical attention.
Ingestion: If swallowed, give 1 or 2 glasses of water or milk. Do not induce vomiting. Contact physician or poison control center immediately.